PlatformIO VS Code: The smarter way to program microcontrollers?
Full story: digikey.com/en/maker/blogs/2…
5
12
926
Akira retweeted
こないだのイベントでいただいたCardputerを使ってみた。USBでつないで、CCに「cardputer試したい」って入れるとサンプルアプリを書いてファームをアップロードしてくれた。PlatformIOのビルドやUSB設定でハマったり、ググって慣れないArduinoコード書いてた日々はなんだったんや...
3
14
5,738
Jun 15
This guy created an AirTag for lost drones and made $156,211.
His device catches a quadcopters last signal and leads you to it.
Finder returns it to the owner and claims a reward.
Build the same recovery setup with a $9 device and Claude:
It logs each drone's live GPS, altitude, and the pilot's location.
When a drone falls, you walk to its last reported coordinates.
Parts: one ESP32-S3 or ESP32-C3 board, around $6.
Use the S3 or C3, not the old ESP32, because they catch Bluetooth 5 Long Range.
Add a $3 OLED screen if you want to read coordinates in the field.
Power it from any USB power bank you already own.
Firmware: clone the PeterJBurke/RID project, which runs on the OpenDroneID core.
It is a PlatformIO project, so open it in VS Code with the PlatformIO extension.
Plug in the board and hit Upload.
Open the serial monitor to read every drone's lat and lon.
For a live map instead, flash the Mesh Mapper firmware and run its Flask server.
Now bring in Claude Code to handle the boring part.
Tell it to configure your board, fix compile errors, and give you the flash command.
Tell it to beep when a new drone appears and to log the last position on signal loss.
Tell it to add a NEO-6M GPS so the device shows distance and bearing to the drone.
To find a downed drone, paste the last coordinates into your phone map and walk there.
It only sees drones that actually broadcast Remote ID, so old or DIY builds stay invisible.
Range is a few hundred meters, so you have to be near the flight path to catch it.
To track your own drone reliably, put a beacon on it instead of building a receiver.
Fizikçiler buna cevap versin.. Drone sabit mi yoksa saate 60 km hızla hareket mi ediyor?
5
5
50
5,137
FreeCAD (CAD CAM CAE) retweeted
Check this out: DIY Left-Hand Controller Designed Specifically for FreeCAD by Xian DIY in PlatformIO, PCBWay, and Raspberry Pi hackster.io/xian886mev/diy-l…
1
14
988
傑作マイコン M5Stamp S3 の後継機種が出るのか!
PlatformIO 開発だから少し遅れて参戦だが、使える日が来るのが待ち遠しいぜ
更新：ESP32-P4ベースの組み込みモジュール「M5Stamp ESP32P4」が入荷 akiba-pc.watch.impress.co.jp…
10
Jun 15
ないです。自動判別のはずなんですよね。。。
VSCode PlatformIOの場合はlib_depsに
M5GFX@0.2.22
M5Unified@0.2.27
の順番に書いて、一度、ソースツリーの.pioを削除してからビルドしてみるでしょうか。
1
34
I think PlatformIO -> VSCode familiarity opened up a lot of doors for folk, and I guess Micro/CircuitPython opened up a lot of doors for a lot of folk also.
It was cool in the ATMEGA days, where you could bootstrap yourself easily.
Modern 'duinos seem awfully niche, in a way.
1
22
Chris Meier retweeted
#ProjectSpotlight 🚀 "How to build a simple Telegram-controlled video surveillance system with ESP32 on PlatformIO"
👉 techrm.com/how-to-build-a-si…
📌 #EmbeddedSystems #Semiconductor #Engineering #Electronics #Hardware #SmartHome #HomeSecurity #IoT #DIY
2
18
1,006
Jun 13
The Edge Gateway:
Wrote the ESP32 firmware using PlatformIO w/ progressive testing:
- Validated ESP-to-laptop MQTT traffic over our local broker.
- Verified packet delivery rates.
- Designed the JSON payloads to transmit vital health data (battery, seed count, GPS coordinates)
1
39
Jun 13
Jadi mau ga mau kalau mau build, pake VSCode Platformio. Cuma karena temen ga bisa pake Platformio, mau ga mau harus pake Arduino IDE lagi
9
Jun 13
А не хочете спробувати PlatformIO для роботи з кодом для ESP32. Це українська розробка.
2
1
93